Remote Monitoring for Pumps and Tanks: What to Measure and What It Prevents
November 11, 2026 · 4 min read · Etzal Group Team
A pump station at the edge of an estate, a rooftop water tank, a fuel tank behind a factory. These assets share two traits: nobody stands next to them, and when they fail, somebody notices only after the damage is done. Remote monitoring for pumps and tanks is one of the most practical first IoT projects, because the measurements are simple and the failures are expensive.
What goes wrong
Start from the failures, because they decide what to measure.
- Dry running. A pump operating without liquid overheats and destroys its seals within minutes.
- Overflow. A tank filling past its limit wastes product and can cause flooding or contamination.
- Running empty. A tank that reaches zero stops whatever depends on it: a building's water supply, a generator, a production line.
- Leaks. Losses that go unnoticed for weeks in buried or remote pipework.
- Pump wear. Bearings, impellers and seals degrade gradually, then fail suddenly.
- Blockage. A clogged strainer or pipe makes the pump work harder for less flow.
- Short cycling. A pump starting and stopping too often, usually from a faulty pressure switch or a waterlogged pressure vessel, which wears the motor.
- Power problems. Phase loss or low voltage that damages motors.
What to measure
A small set of signals covers most of these.
Tank level. Continuous level from a pressure, ultrasonic or radar sensor, with independent float switches for high and low limits as a backup.
Pressure. At the pump outlet, and at the inlet where suction conditions matter. Pressure that is low while the pump runs points to dry running, a leak or wear.
Flow. From a flow meter with a pulse or analogue output. Combined with pressure it shows how well the pump performs. Totalised flow gives consumption.
Motor current. A current transformer on one phase tells you whether the pump is running and how hard it is working. Low current suggests dry running or a broken coupling. High current suggests blockage or mechanical trouble.
Run status and run hours. When the pump starts and stops, how many starts per hour, and total hours for maintenance planning.
Temperature and vibration. For larger or critical pumps, bearing temperature and vibration give early warning of mechanical wear.
Power quality. Voltage and phase presence, where supply problems are common.
Not every site needs all of these. A small booster set may need level, pressure and current. A critical transfer pump justifies the full list.
From readings to protection
The value comes from combining signals.
- Dry-run detection. Pump running, current low, pressure low. Stop the pump locally and alert.
- Leak detection. Flow recorded at night when no use is expected, or a tank level falling while the outlet valve is closed.
- Overflow prevention. High level alarm before the limit, with the fill pump or valve stopped locally at the high-high float.
- Days to empty. Current level divided by recent consumption, so a refill is ordered in time.
- Efficiency trend. The same pressure and flow needing more current over the months is a sign of wear.
- Cycle count. More starts per hour than the motor is rated for indicates a control problem.
Protective actions such as stopping a pump should happen at the site, in the local controller, so that they work without a network connection. The remote system reports and records.
Connectivity and power
Many of these sites have no network cable and sometimes no mains power.
- Cellular suits sites with coverage and a steady data need.
- LoRaWAN suits clusters of low-data points within a few kilometres of a gateway.
- Solar with battery powers sensors and a gateway where there is no supply. Size it for the cloudy season, not for an average day.
Whatever the link, the gateway should store readings during outages and forward them later.
Alerts worth sending
Keep the list short:
- Level high or low, after a delay.
- Pump commanded on and not running.
- Dry-run condition.
- Abnormal night flow.
- Excessive starts.
- Device offline or battery low.
Each alert names the site, the value and the first thing to check.
Reports that pay for the system
- Daily and monthly consumption per site.
- Pump run hours against the maintenance schedule.
- Number of incidents avoided or caught early.
- Sites ranked by unusual behaviour.
Run hours alone often change maintenance from fixed calendar visits to servicing based on actual use.
A sensible first project
Choose five to ten sites with a history of problems. Fit level, pressure and current monitoring. Run for two months, compare with the manual log, and count the events that were caught. That evidence decides the roll-out better than any estimate.
We design, install and commission systems of this kind in our IoT and Control projects, from sensor selection to dashboards and alerts. If you operate pump stations or tank farms and rely on site visits to know their state, tell us how many sites and what they hold.
Summary
Measure level, pressure, flow, current and run hours. Combine them to detect dry running, leaks, overflow and wear. Keep protective actions local, send a short list of meaningful alerts, and use run hours and consumption data to plan maintenance and supply.
Frequently asked questions
Which sensor is best for measuring tank level?
It depends on the liquid and the tank. Submersible pressure sensors suit clean water and deep tanks. Ultrasonic and radar sensors measure from above without touching the liquid, which helps with corrosive or dirty contents. Float switches are a simple, reliable backup for high and low limits.
Can monitoring be added to old pumps?
Usually, yes. Motor current can be measured with a clamp-on transformer, run status can be taken from the starter, and pressure or level sensors can be fitted to existing pipework. The pump itself does not need to be modern.
Does remote monitoring replace site visits?
It replaces the visits made only to read a gauge or check that something is running. Physical inspection and maintenance are still needed. Monitoring tells you which site needs a visit and what to bring.
Related service
WhatsApp AI Chatbot
We build, train, and run a WhatsApp AI agent that answers customers 24/7, qualifies leads, and follows up.
