Retrofitting Sensors in an Older Building: What Is Worth Measuring and How to Do It Without Rewiring
November 11, 2026 · 6 min read · Etzal Group Team
A twenty-year-old office building of fourteen floors has a building management system that one technician understands, a single electricity bill for the whole property, and tenants who complain that the eighth floor is cold and the eleventh is hot. The owner is quoted a large sum to replace the whole system and hesitates. There is a smaller question worth asking first: what would we do differently if we could see what the building is doing? Retrofitting sensors is how to find out, floor by floor, without opening ceilings across the property.
Start from decisions, not devices
List the decisions that better data would change.
- Which equipment runs when nobody is there?
- Which floors or tenants use the most energy per square metre?
- Is the chiller plant running efficiently, or just running?
- Where are the comfort complaints justified?
- Which equipment is about to fail?
- Can tenants be billed for what they actually use?
Each decision points to a few measurements. Measuring everything because sensors are cheap produces dashboards and no action.
What is usually worth measuring
In rough order of payback.
1. Electricity, divided
- Main incomer, at fifteen-minute intervals or finer.
- Major loads: chillers, pumps, cooling towers, air handling units, lifts.
- Each floor or tenant, lighting and power.
The first finding in most buildings is the night and weekend load: equipment that runs because nobody switched it off or because a schedule was overridden years ago.
2. Cooling plant
- Chilled water supply and return temperatures.
- Flow, where it can be measured.
- Chiller and pump power.
Together these show how much cooling is delivered per unit of electricity. A plant that looks fine can be far from its efficient point.
3. Space conditions
- Temperature and humidity in occupied zones, several per floor.
- Carbon dioxide in meeting rooms and dense areas, as an indicator of ventilation.
These settle comfort disputes with facts and reveal overcooling, which is common and expensive.
4. Water
- Main meter and sub-meters by block or riser.
- Leak detectors in plant rooms, pantries and under raised floors.
- Tank levels.
5. Equipment condition
- Vibration and temperature on pumps, fans and motors.
- Run hours and start counts.
- Filter differential pressure on air handling units.
6. Occupancy
- Presence or people counting by zone, to match cooling, lighting and cleaning to actual use.
Handle occupancy data with care for privacy: count, do not identify, and tell occupants what is measured.
Avoiding new cabling
Wireless sensors
- Low-power long-range networks, such as LoRaWAN, suit sensors that send small readings every few minutes. One or a few gateways can cover a building, with batteries lasting years.
- Mesh protocols suit dense indoor deployments.
- Cellular suits isolated points such as a remote pump room.
Test coverage before buying. Concrete cores, basements and plant rooms block signals. Carry a test sensor through the building and record where it is heard.
Energy metering without shutdowns
Clamp-on or split-core current sensors fit around existing cables. Voltage is taken from a spare breaker. A qualified electrician must do the work, with the proper safety procedure, and some boards are too crowded or too old to work in safely without a planned outage.
Reading what already exists
Many chillers, variable speed drives, meters and lifts already have a communication port, commonly Modbus or BACnet. A gateway can read these and add them to the platform at low cost. Ask the equipment supplier for the points list.
Working with an old building management system
Three situations.
- It has a standard interface. Read its data into the new platform. Keep it in control.
- It is closed or undocumented. Leave it running and overlay independent sensors. Monitor first, control later.
- It is failing. Plan a staged replacement, and use the sensor data to specify what the new system must do.
The overlay approach has a real advantage: it shows what the old system is actually doing, including schedules and setpoints nobody remembers setting.
Keep monitoring networks separate from the building's control network and from the office network, with access controlled and remote access secured.
A phased plan
Phase 1: see, six to eight weeks.
- Main and major-load electricity.
- Chilled water temperatures.
- Space temperature on two or three problem floors.
- Baseline for a month.
Phase 2: act on the obvious, one to three months.
- Fix schedules and overrides.
- Adjust setpoints.
- Address simultaneous heating and cooling, stuck valves, equipment left in manual.
These measures often cost almost nothing and deliver the largest early saving.
Phase 3: extend.
- Floor or tenant sub-metering.
- Water and leak detection.
- Condition monitoring on critical equipment.
- Occupancy where it will drive control.
Phase 4: control and optimise.
- Alerts for abnormal consumption.
- Automated schedules based on occupancy.
- Plant optimisation, and replacement decisions backed by measured data.
Proving the saving
- Baseline energy for a comparable period before changes.
- Adjust for weather, occupancy and operating hours, which move consumption on their own.
- Measure after each change.
- Report energy per square metre and night load as a share of day load.
Agree the method before starting. A saving that cannot be explained will not be believed by whoever approves the next phase.
Practicalities that decide success
- Naming. Every sensor has a clear name with building, floor, zone and equipment.
- Records. A list and floor plan of every device, with install date and battery date.
- Maintenance. Someone replaces batteries and checks dead sensors monthly.
- Calibration. Check a sample against a reference instrument yearly.
- Ownership. Named people receive alerts and have authority to act.
- Data ownership. The contract lets you export all data and keep it if you change supplier.
- Tenants. Tell them what is installed and why.
Common mistakes
- Installing hundreds of sensors before deciding what to do with the data.
- Metering only the main supply, which shows that energy is used and not where.
- Skipping the coverage test.
- Ignoring data already available from chillers and drives.
- Replacing the building system before understanding the building.
- Dashboards without alerts or owners.
- No baseline.
- Nobody responsible for batteries.
- Connecting monitoring devices to the office network without separation.
We design and deliver building monitoring retrofits, from metering and wireless sensors to integration with existing systems, as part of IoT and Control Systems. If you want to see what your building is doing before deciding what to replace, contact us.
Summary
Begin a retrofit from the decisions you want to make, then measure what informs them: divided electricity, the cooling plant, space conditions, water and equipment condition. Use wireless sensors, clamp-on metering and data already available from equipment to avoid rewiring, and overlay an old building system without replacing it. Work in phases, fix schedules and setpoints first, prove savings against an adjusted baseline, and assign people to act on alerts and maintain the sensors.
Frequently asked questions
What should be measured first in an older building?
Start with energy: the main incoming supply and the largest loads, which are usually chillers or air conditioning, air handling, lifts and lighting by floor. Then add temperature and humidity in occupied areas, and water. These few measurements show where consumption goes and when, and they usually reveal waste outside working hours.
Can sensors be added without new cabling?
In most cases, yes. Battery-powered wireless sensors for temperature, humidity, occupancy, door state, leaks and vibration need no wiring. Energy meters with clamp-on current sensors can be installed in a distribution board without cutting cables, though the work must be done by a qualified electrician with suitable isolation and safety procedures.
Do we have to replace the existing building management system?
Usually not. An overlay of sensors and a separate monitoring platform can work alongside an older system, reading from it where it offers a standard interface and adding measurements it lacks. Replacement makes sense only when the old system is failing, unsupported or unable to control equipment you need to control.
Related service
WhatsApp AI Chatbot
We build, train, and run a WhatsApp AI agent that answers customers 24/7, qualifies leads, and follows up.
