AI & Automation

Finding Water Loss With District Metering: A Practical IoT Approach for Utilities, Estates and Large Sites

November 11, 2026 · 6 min read · Etzal Group Team

An industrial estate buys water in bulk and distributes it to sixty tenants through its own pipes. Each month it pays the supplier for 180,000 cubic metres and bills tenants for 131,000. The difference, more than a quarter, is absorbed as a cost. The estate manager knows there are leaks and has no idea where. Crews dig where water surfaces, which is rarely where the largest loss is. Water loss cannot be managed as one number for the whole network. It has to be divided until it points at a place.

Two kinds of loss

  • Physical loss: leaks in mains and service connections, bursts, overflowing tanks. The water was produced or bought and never reached anyone.
  • Commercial loss: water that reached a user and was not billed correctly. Under-registering old meters, estimated readings, data entry errors, illegal connections, bypassed meters.

They need different remedies. Leak detection does nothing for a meter that reads twenty percent low. A good programme measures both.

Divide the network into zones

A zone, often called a district metered area, is a part of the network with:

  • Known boundaries, closed by valves.
  • One or a few inlets, each with a flow meter.
  • A known list of customers inside.

For each zone, the balance is simple: water in, minus water billed, equals loss. A network of five zones tells you which zone to work on first. A zone of two thousand connections is typical for a utility. An estate or campus may have zones of a few buildings each.

Before trusting a zone, test that it is truly closed: shut the inlet briefly and confirm that pressure inside falls.

Minimum night flow

Total loss per month is too slow and too blunt. Flow at night is fast and sharp.

Between roughly two and four in the morning, legitimate use is minimal. The flow entering the zone at that time is mostly leakage plus a small, estimable amount of night use.

  • A stable night flow is the zone's background leakage.
  • A step up means a new leak or burst.
  • A step down after a repair proves the repair worked and measures the saving.

Plotted daily, night flow turns leak detection from a search into a response. Be aware of legitimate night users, such as factories running three shifts or tanks that fill at night, and account for them.

Pressure matters as much as flow

Leakage rises with pressure, and bursts follow pressure surges.

  • Log pressure at the inlet, at the highest point and at the far end of each zone.
  • Look for excess pressure at night, when demand is low and pressure climbs.
  • Consider pressure management: a regulating valve that lowers pressure when demand is low can cut leakage and burst frequency across a whole zone without digging anything.
  • Watch for transients from pumps starting and stopping.

Pressure data also protects service quality: it shows that customers at the far end still receive enough.

The equipment

At each zone inlet

  • Flow meter. Electromagnetic meters are common for accuracy across a range of flows. Insertion or clamp-on ultrasonic meters suit pipes that cannot be cut. Size the meter for low night flows, not only for peak.
  • Pressure sensor.
  • Data logger with battery and cellular or low-power network communication, sending at intervals of five to fifteen minutes.
  • A chamber that stays accessible and does not flood the electronics, or equipment rated for submersion.

Inside the zone

  • Pressure loggers at critical points.
  • Customer meters. For large users, meters with remote reading give daily or hourly consumption, which sharpens the balance.
  • Acoustic loggers or correlators, fixed or mobile, to pinpoint a leak once the zone is known.
  • Level sensors in tanks, to catch overflows.

In the office

  • A platform that stores readings, computes night flow and balance per zone, and raises alerts.
  • A link to billing data, so consumption per zone can be totalled.
  • A map of the network with zones, valves and repair history.

A pilot in one zone

Three to four months.

  1. Choose the zone: suspected high loss, clear boundaries, manageable size.
  2. Verify the boundary and record every valve position.
  3. Install inlet flow and pressure monitoring, plus two or three pressure points.
  4. Collect two to four weeks of baseline: inflow, night flow, pressure.
  5. Check customer meters for the largest users. Test or replace suspect ones.
  6. Compute the balance: inflow against billed consumption for the same period.
  7. Find leaks: step testing, by closing sections at night and watching the flow drop, then acoustic survey.
  8. Repair, and record each repair with location and estimated flow.
  9. Measure again. Night flow before and after.

The result is a figure in cubic metres per day recovered, with a value attached.

The figures that prove it

  • Zone loss in cubic metres per day and as a share of inflow.
  • Minimum night flow, before and after.
  • Loss per connection per day, or per kilometre of main, which compares zones fairly.
  • Repairs made and time from alert to repair.
  • Commercial findings: meters replaced, unbilled connections found, and the billed volume gained.
  • Value: recovered volume multiplied by the cost of producing or buying it, plus added billing.

Percentages alone mislead, because they move when consumption changes. Track volume.

Keeping the gain

Leaks return. Networks age.

  • Night flow alerts per zone, sent to a named person.
  • A target repair time from alert to fix.
  • Meter replacement by age and class, starting with the largest users.
  • Monthly review of zone balances.
  • Updated maps after every change.

Without this routine, loss drifts back within a year or two.

Beyond utilities

The same method works for any site that distributes water.

  • Industrial estates reselling water to tenants.
  • Hotels, hospitals and campuses: a sub-meter per building and a night flow check catches running toilets, leaking underground pipes and stuck valves.
  • Factories: water per production area, tied to output.
  • Apartment and office buildings: per riser or floor.

For a building, a night flow that never reaches near zero is a leak or a fixture left running.

Common mistakes

  • Treating loss as one network-wide percentage.
  • Zones that are not really closed, making the balance meaningless.
  • Inlet meters too large to register night flow.
  • Chasing leaks and ignoring meter under-registration.
  • No pressure data.
  • Monitoring without a repair crew and budget to act on alerts.
  • Flooded chambers and dead batteries with nobody assigned to maintain loggers.
  • Billing data that cannot be grouped by zone.
  • Declaring victory after one repair campaign.

We design and deliver flow, pressure and level monitoring with alerts and reporting as part of IoT and Control Systems. If you distribute water and cannot say where a quarter of it goes, contact us.

Summary

Water loss becomes manageable when the network is divided into closed zones with metered inlets. Continuous inflow and pressure, and above all minimum night flow, show which zone is losing water and when a new leak appears. Start with one zone, establish a baseline, check large customer meters, find and repair leaks, and measure the recovered volume. Then keep the gain with alerts, repair targets and regular review.

Frequently asked questions

What is non-revenue water?

It is the difference between the volume of water put into a distribution system and the volume billed to customers. It includes physical losses, such as leaks and overflows, and commercial losses, such as meter inaccuracy, billing errors and unauthorised use, as well as authorised but unbilled use such as firefighting.

What is a district metered area?

It is a section of a water network that has been isolated so that all water entering it passes through one or a few metered points. By measuring inflow continuously and comparing it with consumption inside the zone, the operator can calculate the loss in that zone and see changes within days.

Why is night flow measured?

Because in the small hours, customer use is at its lowest, so most of the flow entering a zone is leakage. A minimum night flow that is high, or one that rises from one week to the next, points to a leak or a burst inside the zone. It is the simplest and most informative single indicator for physical losses.

Author

Etzal Group Team

Etzal Group Team, helping businesses grow with technology. Contact us.

Related service

WhatsApp AI Chatbot

We build, train, and run a WhatsApp AI agent that answers customers 24/7, qualifies leads, and follows up.